久久国产精品午夜一区_91精品國產高清久久久久久91_?级毛片免费全部播放_欧美色图在线视频一区二区三区_国产综合亚洲一区二区三区_中文字幕熟女网_国产精品男人爽免费视频_九九无码网战_亚洲日本三级电影在线观看_欧美日韩DVD手机在线不卡

| 注冊| 產品展廳| 收藏該商鋪

行業產品

當前位置:
廣東宏展科技有限公司>>技術文章>>ASTM D4329-05測試標準

產品分類品牌分類

更多分類

ASTM D4329-05測試標準

閱讀:1983        發布時間:2018-7-23

本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用,為確保測試結果的準確性、節省您的時間,如需ASTM D4329-05標準詳細信息或ASTM D4329-05具體測試方法,歡迎與我們技術人員聯系或給我們留言,我們將為您相關的技術支持。

 

ASTM D4329-05標準介紹

塑料熒光紫外線暴露測試的標準測試方法:

本測試方法規定了依照G151和G154測試方法對塑料進行熒光紫外線暴露測試的具體程序和測試條件。

 

ASTM D4329-05英文版本

This standard is issued under the fixed designation D 4329; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.

 

1. Scope*

1.1 This practice covers specific procedures and test conditions that are applicable for fluorescent UV exposure of plastics conducted in accordance with Practices G 151 and G 154. This practice also covers the preparation of test specimens, the test conditions best suited for plastics, and the evaluation of test results.

1.2 The values stated in SI units are be regarded as standard. The values given in brackets are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

NOTE 1—This practice is technically similar to ISO 4892-3.

 

2. Referenced Documents

2.1 ASTM Standards:

D 3980 Practice for Interlaboratory Testing of Paint and Related Materials

D 5870 Practice for Calculating Property Retention Index of Plastics

E 691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

G 113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials

G 141 Guide for Addressing Variability in Exposure Testing on Nonmetallic Materials

G 147 Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests

G 151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices That Use Laboratory Light Sources

G 154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

G 169 Guide for Applications of Basic Statistical Methods to Weathering Tests

G 177 Tables for Reference Solar Ultraviolet Spectral Distributions: Hemispherical on 37 Degree Tilted Surface

2.2 ISO Standard:

ISO 4892-3 Plastics—Methods of Exposure to Laboratory

Light Sources—Part 3, Fluorescent UV Lamps

2.3 SAE Standard:

SAE J2020 Accelerated Exposure of Automotive Exterior Materials Using a Fluorescent UV and Condensation Apparatus

 

3. Terminology

3.1 The definitions in Terminology G 113 are applicable to this practice.

 

4. Significance and Use

4.1 The ability of a plastic material to resist deterioration of its electrical, mechanical, and optical properties caused by exposure to light, heat, and water can be very significant for many applications. This practice is intended to induce property changes associated with end-use conditions, including the effects of sunlight, moisture, and heat. The exposure used in this practice is not intended to simulate the deterioration caused by localized weather phenomena, such as, atmospheric pollution, biological attack, and saltwater exposure.

 (Warning—Variation in results may be expected when operating conditions are varied within the accepted limits of this practice. Therefore, no reference to the use of this practice should be made unless accompanied by a report prepared in accordance with Section 8 that describes the specific operating conditions used. Refer to Practice G 151 for detailed information on the caveats applicable to use of results obtained in accordance with this practice.)

NOTE 2—Additional information on sources of variability and on strategies for addressing variability in the design, execution, and data analysis of laboratory-accelerated exposure tests is found in Guide G 141.

4.2 Reproducibility of test results between laboratories has been shown to be good when the stability of materials is evaluated in terms of performance ranking compared to other materials or to a control.5,6 Therefore, exposure of a similar material of known performance (a control) at the same time as the test materials is strongly recommended. It is recommended that at least three replicates of each material be exposed to allow for statistical evaluation of results.

 

▼ASTM D4329-05第三方檢測機構

以上標準信息來自互聯網搜索整理,如需了解完整的ASTM D4329-05的信息或ASTM D4329-05標準解讀,歡迎詳詢。

收藏該商鋪

登錄 后再收藏

提示

您的留言已提交成功!我們將在第一時間回復您~
二維碼 意見反饋
在線留言
主站蜘蛛池模板: 新干县| 江北区| 玉龙| 赤壁市| 永康市| 宜昌市| 剑川县| 松原市| 丹寨县| 龙胜| 宁南县| 太保市| 屯昌县| 呼和浩特市| 中西区| 牡丹江市| 安泽县| 平舆县| 大足县| 乌兰浩特市| 休宁县| 漾濞| 鸡东县| 上杭县| 桦甸市| 巴中市| 竹溪县| 景宁| 通化县| 玛纳斯县| 石屏县| 桦南县| 色达县| 崇文区| 辽中县| 神农架林区| 宁武县| 岳西县| 津南区| 天气| 江口县|